PSP-1500 With PFC and Parallel Function Switching Power Supply
Features
- High efficiency, high reliability
- AC input inrush current limiting
- Built-in active PFC function, PF>0.95
- Protections: Short circuit/ Over load/ Over voltage/ Over temperature
- Built-in constant current limiting circuit
- Built-in remote ON-OFF control and remote sense function
- 3 years warranty
- Dimensions: 278*129*190.5mm（L*W*H）
| MODEL |
PSP-1500-5 |
PSP-1500-12 |
PSP-1500-13.5 |
PSP-1500-15 |
PSP-1500-24 |
PSP-1500-27 |
PSP-1500-48 |
| OUTPUT |
DC Voltage |
5V |
12V |
13.5V |
15V |
24V |
27V |
48V |
| Voltage Tolerance |
±6.0% |
±3.0% |
±2.0% |
±2.0% |
±1.0% |
±1.0% |
±1.0% |
| Rated Current |
217.5A |
112.5A |
100.5A |
90A |
56.4A |
50.4A |
28.5A |
| Current Range |
0-217.5A |
0-112.5A |
0-100.5A |
0-90A |
0-56.4A |
0-50.4A |
0-28.5A |
| Rated Power |
1087.5W |
1350W |
1356.75W |
1350W |
1353.6W |
1360.8W |
1368W |
| Peak Value Power |
1200W |
1500W |
1500W |
1500W |
1500W |
1500W |
1500W |
| Ripple & Noise |
100mVp-p |
150mVp-p |
150mVp-p |
150mVp-p |
150mVp-p |
150mVp-p |
200mVp-p |
| DC Adjustment Range |
-5%,+10% |
-17%,+10% |
±11% |
-10%,+20% |
-17%,+10% |
±11% |
-15%,+17% |
| Setup, Rise, Hold Time |
1.5s,50ms,15ms/230VAC at full load |
| INPUT |
Voltage Range |
176～264 VAC 47-63Hz；248～370VDC |
| Power Factor |
PF>0.95/230VAC at full load |
| AC Current |
10.5A/230 VAC |
| Efficiency |
77% |
84% |
84% |
84% |
85% |
85% |
86% |
| Inrush Current |
Cold start 100A/230VAC |
| Leakage Current |
<3.5mA/240VAC |
| PROTECTION |
Over Load |
115%~140% |
| Protection: Constant current limiting, recovers automatically after fault condition is removed |
| Over Voltage |
115%～135% |
| Protection type: Shut down o/p voltage, re-power on to recover |
| Over Temp |
95 (TSW1) Detect on the heatsink of PFC MOSFET 90 (TSW2) Detect the winding of output choke |
| Protection:Shut down o/p voltage, recovers automatically after temperature goes down |
| FUNCTION |
Remote Control |
RC+/RC-：0~0.8V Power on, 4~10V Power off, sink current <30mA |
| ENVIRONMENT |
Working Temp., Humidity |
-10℃～+65℃；20%～90 %RH |
| Storage Temp., Humidity |
-20℃～+85℃；10%～95 %RH |
| Vibration |
10～500Hz，2G 10min./1cycle, period for 60min, each along X, Y, Z axes |
| SAFETY |
Withstand Voltage |
I/P-O/P:3KVAC I/P-O/P:1.5KVAC O/P-FG: 0.5KVAC |
| Isolation Resistance |
I/P-O/P, I/P-FG, O/P-FG: 100M Ohms / 500VDC |
| STANDARD |
Safety Standard |
Design refer to UL1950,TUV EN60950 |
| EMC Standard |
Design refer to EN55022,EN61000-3-2,-3,EN61000-4-2,3,4,5,6,8,11;ENV50204,EN55024 |
| OTHERS |
Weight |
7.4Kg |
| Packing |
2pcs/15.5Kg/1.28 CUFT |
| NOTE |
1.All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature.
2.Ripple & noise are measured at 20MHz of bandwidth by using a 12″twisted pair-wire terminated with a 0.1μ &47μ parallel capacitor.
3.Tolerance: includes set up tolerance, line regulation and load regulation.
4.10% Duty cycle maximum within every 30 seconds(max.). Average output power should not exceed the rated power.
5.The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. |
|
